Avoid Dark Mode hack cheats.I have an HP LaserJet 1020, which I obtained in 2007, and after much fuss, managed to get the workaround for the Mac I had at the time.
![]() Hp Printer Software Sierra Install Mac OSApart from that, it has to be a Sandy Bridge processor. As you might’ve read in the hackintoshing basics post, it’s all about the motherboard, and the HP ProBook seems to have a hackintoshable motherboard. Recently, one of the members of the tonymacx86 community, named ‘BlueKing’ discovered that the HP ProBook (especially the 4530S) is one of the most compatible laptops for running Mac OS X Lion or Snow Leopard (not to mention it resembles a MacBook Pro as well). And if you remember, we have already showed you how to install Mac OS X Snow Leopard or installing Mac OS X Lion on a custom-built computer using the tonymacx86 methods. The results vary, so hope for the best, and proceed with caution.If you’re familiar with hackintoshing, you might know that the hackintoshing methods devised by tonymacx86 are the most ‘legal’ ones (since they do not involve piracy, while most other methods are based on piracy). Then just take the old one out, and replace it with the new one. Be sure to order the right one, HP branded card, part number 593127-001 (just search on eBay for HP Atheros 593127 and you’ll get it). But if you’ve just purchased a ProBook and don’t have the required card (you might have a Broadcom or Ra-link instead), you can buy the Atheros card from eBay for pretty cheap. If you want to use Wi-Fi in OS X, your laptop should have an ‘Atheros’ Wi-Fi module. Finally, there’s one more thing that you need to check. So if you are an existing ProBook owner, see if your machine is compatible or not. Ms outlook send later for macBackup your data before you proceed. Either way, we want it to be formatted on GPT (so you might have to reformat it if Windows is already installed). Either you’ll have Windows (or any other OS) already installed on the hard drive, or it might be empty. The following procedure is a detailed explanation of the Lion install guide by BlueKing (for snow leopard installation, you may also refer to this guide).There may be two situations now. You can also install Mac OS X Snow Leopard on your ProBook or any other laptop (instead of Lion) as described in the iBoot+MultiBeast method. But in short, buy the OS X Lion app on a Mac, attach a USB of 8GB or more capacity, format it as Mac OS X Extended, download UniBeast from tonymacx86, run it, be sure to select “Laptop Support” when you run it, wait, voila.Once the USB is ready, attach it to your ProBook, and turn it on. Explaining the whole thing will take time. We have a detailed guide on that, so you definitely need to check it out. Start off by preparing the UniBeast USB drive. In Disk Utility, click the Partitions tab. You can make even more (or lesser) partitions if you want to. Now, assuming you want to have a dual-boot system, we will create 3 partitions One for Mac, one for storing your data, and one for Windows. Boot from the USB into the installer (press F9 when you turn on your ProBook), let it load, select a language, and click Next.Then on the menu bar, click Utilities> Disk Utility. Also note down the BIOS version, since we will need that later. If you want to dual-boot with Windows, it is usually recommended to install Windows first, and then install OS X. You may notice that the ‘Windows’ and ‘Empty’ Partitions aren’t labelled here, but you get the idea.Once you’ve done partitioning, quit disk utility. This one is just to give you an idea of how it would look like. Click Apply, and then click Partition to partition the drive.This screenshot is just for reference, actual results may vary. Make sure the Windows and Empty partitions are formatted as MSDOS and the Mac OS X partition is formatted as Mac OS X Extended (Journaled). Click the Options button, click ‘GUID Partition Table’, and click OK. Do so by clicking the restart button.When it restarts, you’ll need to boot from the installer USB again. When it’s done, you’ll be informed that Mac OS X Lion has been installed, and will be prompted to restart your computer. It takes about 15-30 minutes, depending on your configuration. Select the Mac partition as the destination (whatever you named it, Lion, or Mac HD), and let it install. Continue with the installer. You’ll be on the desktop in a few seconds. Use the arrow keys to select the drive named Lion (or whatever you named it) and press enter. Either to boot into the installer again, or to boot into OS X that you just installed (and that’s what you need to do). But in this case, the specially designed HP ProBook installer is what you need. And if you’ve been following this guide for any Sandy Bridge laptop other than a ProBook, you have to use MultiBeast now ( read how to use it). If you remember, it’s important to run MultiBeast after you install OS X on a custom-built PC so that you can ensure the operation of all the devices, such as sound, and other functions like sleep. Since this project of hackintoshing a ProBook was started by a member of the tonymacx86 forums, he also developed a special installer, specifically for the ProBook. Attach a USB keyboard to the laptop and the prompt will disappear, then you can unplug the keyboard.There’s one more thing left to do before you can fully enjoy using Mac OS X on your laptop. Select your BIOS version (you probably would’ve noted it down earlier, so refer to that). There are a couple of selections you need to make. Download the installer and run it. And if you’re installing on a different laptop, use MultiBeast.The next step is the simplest. We are not authorized to redistribute it, so you’ll have to go and get registered, and download it. After registering, download the installer attached at the end of THIS post. Click the arrow besides the name to expand the items under that category. First, identify which version of ProBook you have, whether it is the one with built-in graphics support (HD3000), or one with dedicated graphics (Radeon), or the 4730S. Finally, the most essential thing, select the appropriate DSDT. Also select Ethernet Kext Installer, Chimera (bootloader), and the appropriate SSDT if you’re on an i5 or i7 CPU. Select the OS X version that you’ve just installed (in case of Snow Leopard, upgrade to 10.6.8 before running the installer). It means if something stops working, you can run the installer again to re-enable it. Remember, you can run the installer any time again, if you need to. When that’s done, you can test if everything is working. The following screenshot shows how the selections looked like on my ProBook.Once you’ve made your selections, click Install, enter your password, and wait for the installation to complete. Also check out the Extra Tools and see if you want to install any of them. This is normal because Windows has replaced the chimera bootloader. Once Windows has been installed, you’ll notice that you can no longer boot into OS X. If you want a dual boot system with Windows, boot using the Windows DVD, and install Windows on the partition that we specified using disk utility (you can format the Windows partition as NTFS from the Windows setup, and the empty partition as FAT32 after you install Windows, so that both Windows and OS X can read/write data on it). The tonymacx86 community is now working on bringing multi-touch gestures to the trackpad (although two finger swipe/scrolling works perfectly).Now if you’re happy with how your ProBook is running OS X, you can continue using it. Run the ProBook installer and install chimera (select chimera from the list of items to install).
0 Comments
Leave a Reply. |
AuthorClaudia ArchivesCategories |